Fused
- How
- The interlining is bonded to the cloth with heat and adhesive
- Best for
- Volume roles, short programmes, tight budgets
- Watch out for
- Repeated dry cleaning and heat break the bond. That is the bubbling
Canvas, Super numbers and weight
You have seen it on a jacket somewhere. Small ripples across the chest or along the lapel that were not there when it was new, and that no amount of pressing removes. That is a glue layer coming apart, and it is decided by how the jacket was built, not by how it was treated.
This page explains the three ways a jacket front is made and what each one costs you over three years. It is the question a corporate suit supplier should raise first and almost never does. We cut and stitch tailored suits and blazers in Ajman, minimum order 25 pieces, across all seven emirates.
The numbers behind a jacket
Canvas construction, Super number and cloth weight. Three questions, and most quotes in this market answer none of them unless asked.
The thing that decides everything
Between the outer cloth and the lining of a jacket front sits an interlining. How that interlining is attached is the single biggest decision in tailoring, and it is invisible from the outside until the day it is not.
Once the adhesive has let go in patches, the cloth and the interlining move independently. Pressing flattens it for a day and the ripples return, because nothing is holding the two layers together any more.
There is no repair. The jacket is replaced. That is why the canvas question is a cost question rather than a quality preference, and why it belongs in the first conversation.
Pinch the cloth of the lapel gently between thumb and forefinger and roll the two layers against each other. On a canvassed jacket you can feel a third layer floating between them. On a fused jacket the front feels like one solid board.
It takes five seconds and it is the only way to check without cutting the garment open.
A number that gets misread constantly
The Super number describes how fine the wool fibre is. It is a measurement, not a grade, and for a garment worn four days a week a higher number is usually the wrong choice.
| Super number | Character | Suits | Weakness in daily wear |
|---|---|---|---|
| Super 100s | Robust, slightly dry hand | High-wear roles, security, front of house on its feet | Less drape and less lustre than finer cloths |
| Super 110s to 130s | Balanced. Soft enough, tough enough | Most corporate programmes across most tiers | None worth naming. This is the practical band |
| Super 150s and above | Very fine, soft, lustrous | Executive garments worn occasionally | Wrinkles readily, wears through at friction points sooner |
Scroll the table sideways on a phone.
A finer fibre is a thinner fibre. It feels luxurious in the hand and it abrades faster at the elbow, the seat and the inside of the cuff, which are exactly the places a daily uniform fails. If a corporate suit supplier is pushing Super 150s for a floor team, they are selling the number rather than the garment.
The UAE question
Suiting cloth is specified by weight in grams per linear or square metre, and the default most suppliers quote was chosen for a European office rather than a Gulf one.
Tropical or summer weight runs roughly 180 to 230 grams per metre. Year-round sits around 250 to 290. Winter cloth starts above 300 and has no business in this market at all.
Indoors at 21 degrees the heavier cloth is fine. The problem is the walk from the car park, the client visit and the forty minutes in a taxi, which is most of what a corporate jacket actually does here.
A fully lined body traps air across the whole back. A half lined or quarter lined jacket leaves the lower back open, which makes a noticeable difference in heat and costs nothing extra to specify.
For a UAE programme, a lighter cloth with a half lined body usually beats a heavier cloth with ventilation gimmicks, and it presses better too.
Make and finish
Pattern match at the pockets. On any check or stripe, the pocket flap should continue the pattern of the cloth beneath it. Where it does not, the cutter was saving cloth.
Working or non-working cuff buttons. A detail, but it tells you how the sleeve was finished and whether alterations will be straightforward later.
Seam allowance left inside. Generous allowance at the side seams and centre back means the jacket can be let out as staff change over three years. A tight allowance means replacement instead of alteration.
Shoulder construction. A structured shoulder reads formal and photographs well. An unstructured one is cooler and more comfortable. Pick by role, not by catalogue.
Branded lining and cuff monogram. Both are done in house, and uniform embroidery services on a jacket sit inside the same production run rather than adding a separate lead time.
A blazer manufacturer that will not send a physical sample before a first production run is asking you to approve something you have not handled.
Before you order
A jacket is the most expensive garment in a corporate programme, and in these five situations the money is better spent elsewhere.
Ordering
Two years or five. It is the honest way to decide fused against half canvas.
Sets the cloth weight and whether the body is half lined.
Most programmes mix. Half canvas above, fused for volume roles, and that is fine.
Chest, waist, sleeve and jacket length per person. Jackets do not forgive guesses.
Where blazers sit alongside shirts, trousers and accessories in one programme that reorders for years, keep the whole specification together with your corporate uniform record rather than per garment.
Questions
Because the interlining was glued rather than stitched. In a fused jacket the interlining is bonded to the outer cloth with heat and adhesive, and repeated dry cleaning and pressing eventually break that bond in patches. The two layers then move independently, which shows as ripples that pressing flattens for a day before they return. There is no repair, so the jacket is replaced. A half canvas or full canvas jacket, where the interlining is attached by stitching, does not do this.
Pinch the lapel gently between thumb and forefinger and roll the two layers against each other. On a canvassed jacket you can feel a third layer floating between the cloth and the lining. On a fused jacket the front feels like a single solid board. It takes five seconds and it is the only check possible without cutting the garment open.
Not for a uniform. The Super number measures how fine the wool fibre is, which is a measurement rather than a grade. A finer fibre is a thinner fibre, so it feels softer and more lustrous while wrinkling more readily and abrading faster at the elbow, seat and cuff, which are exactly where a daily garment fails. Super 110s to 130s is the practical band for most corporate programmes. Super 150s and above suits executive garments worn occasionally.
Roughly 180 to 230 grams per metre, which is the tropical or summer band. Most suppliers quote a year-round cloth of 250 to 290, which was chosen for a European office. Indoors at 21 degrees the heavier cloth is fine, but the walk from the car park and the time in a taxi are most of what a corporate jacket actually does here. Pairing a lighter cloth with a half lined body makes more difference than any ventilation feature.
Usually not, and mixing is normal rather than a compromise. Half canvas for management and client-facing roles where the jacket is worn daily for years, and fused for volume roles or short programmes where the garment will be replaced before the bond fails. The honest way to decide is how long the programme is expected to run before a redesign.
That answer settles fused against half canvas honestly, before anybody talks about price, and it is how a blazer manufacturer should be quoting tailored suits rather than reading from a price list. Send the tiers and the headcount and we will come back the same working day. Minimum order 25 pieces.